![]() Output from sensors (some things is broken.like power usage of APU, temperature of CPU and iGPU and Asus fan): fancontrol-gui (v0.8 and my build from latest git) shows:Īnd in menu " Fans" it shows only fan1 on dGPU1 and fan1 on dGPU2 don`t (both under amdgpu driver) The problem is with hwmon6 (motherboard sensors, pwms and fans). ![]() MINPWM=hwmon6/device/pwm3=0 hwmon6/device/pwm2=45 hwmon6/device/pwm1=0 hwmon1/pwm1=0 hwmon2/pwm1=0 As this isn't really a fix any help is still appreciated.# Configuration file generated by pwmconfig, changes will be lostĭEVPATH=hwmon6=devices/platform/f71882fg.656 hwmon1=devices/pci0000:00/0000:00:02.1/0000:01:00.0 hwmon2=devices/pci0000:00/0000:00:03.1/0000:02:00.0ĭEVNAME=hwmon6=f71808e hwmon1=amdgpu hwmon2=amdgpuįCTEMPS=hwmon6/device/pwm3=hwmon6/device/temp2_input hwmon6/device/pwm2=hwmon6/device/temp2_input hwmon6/device/pwm1=hwmon6/device/temp1_input hwmon1/pwm1=hwmon1/temp1_input hwmon2/pwm1=hwmon2/temp1_inputįCFANS=hwmon6/device/pwm3=hwmon6/device/fan3_input hwmon6/device/pwm2=hwmon6/device/fan2_input hwmon6/device/pwm1=hwmon6/device/fan1_input hwmon1/pwm1=hwmon1/fan1_input hwmon2/pwm1=hwmon2/fan1_input Since I lose control of my fans after my laptop wakes up from suspend, I turned off suspend. I upgraded to Cosmic Cuttlefish to see if that would solve any problems, it didn't. Output of lsmod | grep -i asus: asus_nb_wmi 28672 0įor now I have given up on fancontrol working. So it only finds coretemp, but shouldn't asus be one since that's where the fan control is? If you have some drivers built into your kernel, the list above willĬontain too many modules. To load everything that is needed, add this to /etc/modules: * Chip `Intel digital thermal sensor' (confidence: 9) Sensors-detect output after saying yes for everything: Now follows a summary of the probes I have just done. Starting automatic fan control., but doesn't progress INTERVAL=10ĭEVPATH=hwmon4=devices/platform/asus-nb-wmi Also from switching to Ubuntu from Arch, the place where the pwm that controls the fan switched from hwmon3 to hwmon4 and I don't know if that is any indication as to what could be wrong.įancontrol configuration that I tried to write: Sensors-detect only finds coretemp and because pwmconfig doesn't think I have fan sensors it doesn't generate a config file. If I start my laptop while plugged in the fans will be around 2500 RPM or off. The cpu_fan sensors will either say -1 or 25500 RPM after awakening from hibernate. I tried ignoring this and writing a configuration file for fancontrol, but I couldn't get it to work. ![]() pwmconfig says that I have no working fan sensors. I've had this issue of my fan not working properly on Manjaro, Arch, Fedora, and Ubuntu. See doc/fan-divisors for more information. You may also need to increase the fan divisors. Make sure you have a 3-wire fan connected. There are no working fan sensors, all readings are 0. Giving the fans some time to reach full speed. Physically verify that the fans have been to full speed However, it is ** very important ** that you The program will attempt to restore each fan to full speedĪfter testing. We will attempt to briefly stop each fan using the pwm controls. Note that many motherboards do not have pwmĬircuitry installed, even if your sensor chip supports pwm. This program will search your sensors for pulse width modulation (pwm)Ĭontrols, and test each one to see if it controls a fan on Pwm_config output: # pwmconfig revision 6243 ()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |